One Piece Stainless Steel Ball Valve – Reduced Port, 316, 1000 WOG, PT/NPT/PF, 1/4″–3″ (R-1B)

Produktbeschreibung

A one piece stainless steel ball valve bewertet 1000 WOG, with the body cast as a single piece and welded closed. 316 (CF8M) is the stock material; 304 (CF8) is made to order. PTFE seats, manual quarter-turn lever, reduced port, −20 °C to +180 °C. Two end builds: Weiblich × Weiblich (F×F) von 1/4″ bis 3″ und männlich × weiblich (M×F) in den Größen 1/4″, 3/8″ und 1/2″.

Because the body is one piece instead of two or three bolted or screwed sections, there is no body joint — one fewer place for the valve to leak. The trade-off is honest: it cannot be opened for service, and the bore is one pipe size smaller than the line. We say so plainly further down, and we point you at the valve you should buy instead.

Was „1000 WOG“ eigentlich bedeutet

WOG steht für Wasser, Öl, Gas. Eine Nennleistung von 1000 WOG bedeutet, dass das Ventil für 1000 psi Kaltbetriebsdruck ohne Stoßbelastung on those media.

Three things buyers get wrong about it:

• WOG ist eine Kälteklasse. It is not a steam rating. This valve runs from −20 °C to +180 °C, set by the PTFE seats — tell us your line temperature and we will confirm it suits.
• “Non-Shock” ist Teil der Bewertung. In einer Leitung, in der es zu Wasserschlägen oder einem schnellen Anlaufen der Pumpe kommt, treten Druckspitzen auf, die deutlich über dem normalen Betriebsdruck liegen. Die Dimensionierung muss sich nach der Höhe der Druckspitze richten, nicht nach dem Manometerwert.
• On this valve, “gas” means compressed air. Fuel gas lines (natural gas, propane) call for a gas-listed valve, and this is not one.

Wenn der Druck in Ihrer Leitung im kalten Zustand über 1000 psi liegt, ist dies nicht das richtige Ventil – teilen Sie uns den Druck mit, und wir unterbreiten Ihnen ein Angebot für das passende Ventil.

F×F oder M×F – Was brauchst du?

• Weiblich × Weiblich (F×F) — Beide Enden sind mit einem Außengewinde oder einer Außenverschraubung ausgestattet. Die universelle Wahl und die einzige Variante, die in Größen über 1/2″ (bis zu 3″) erhältlich ist.
• Männlich × Weiblich (M×F) — one male end screws straight into a female port, so you save a fitting and shorten the assembly. Available in 1/4″, 3/8″ and 1/2″ only. If you need M×F above 1/2″, see the two-piece MxF ball valve (1/2″–2″, full port).

Dimensions for both builds are on the PDF dimension sheets at the top of this page.

Technische Daten

Wann man dieses Ventil nicht wählen sollte

Anwendungen

A reduced-port, non-serviceable body is a deliberate trade: the smallest envelope and the fewest joints of the three ball valve body types, at the lowest cost of the three. It belongs where those three things matter more than full flow or in-line repair.

• Instrument and gauge line isolation — the shut-off ahead of a pressure gauge or transmitter, so the instrument can be changed without draining the line. Open it slowly; this is an isolation valve, not a throttling one.
• OEM machinery and skid-mounted systems — small-bore utility shut-offs built into a machine frame or a packaged skid, where the valve is replaced as a unit rather than rebuilt in place.
• Enge Einbauräume — panels, cabinets and pipe runs where a two-piece or three-piece body will not fit. With no mid-body joint there is nothing to add length to the body.
• Compressed air branch isolation — take-offs from a plant air header to a machine, a filter-regulator or a blow-down point.
• Water and oil utility lines — general shut-off on cooling water, wash-down, lubrication and fuel-oil transfer lines up to 1000 psi cold.

Not for pump suction lines (use a full-port valve), fuel gas, steam, potable water or oxygen service — see the table above.

Bei uns einkaufen

• Manufacturer, not a trading company. Our own factory in Taiwan, stainless valves since 1999.
• Mühlenzertifikat auf Anfrage.
• One supplier for the whole line — valves, fittings and strainers, one shipment, one set of documents.

Tell us the size, F×F or M×F, 316 or 304, and the line pressure. That is enough for us to quote.

Häufig gestellte Fragen

What is a one piece stainless steel ball valve?

A ball valve whose body is cast as a single piece and welded closed, instead of being bolted or screwed together from two or three sections. There is no body joint, so there is one fewer place for a line to weep. The trade-off is that the valve cannot be opened for service and the port is reduced — the bore is one pipe size smaller than the line. If you want the same no-body-joint construction with a full-port bore, see the seal-welded two-piece ball valve (V-2B / V-2C).

Was bedeutet 1000 WOG?

WOG stands for Water, Oil, Gas. A 1000 WOG rating means the valve is rated for 1000 psi of cold, non-shock working pressure on those media. It is not a steam rating. On this valve “gas” means compressed air — it is not listed for fuel gas.

Wie groß ist der Betriebstemperaturbereich?

−20 °C to +180 °C, set by the PTFE seats. Tell us your line temperature and we will confirm the valve suits it.

Welche Größen sind erhältlich?

Female × female (F×F) from 1/4″ to 3″ — 1/4″ to 2″ as standard, 2-1/2″ and 3″ on request. Male × female (M×F) in 1/4″, 3/8″ and 1/2″. Dimensions are on the two PDF dimension sheets at the top of this page.

Welche Gewindenormen liefern Sie?

PT (konisch) ist das Standardgewinde; NPT und PF sind ebenfalls vorrätig.

316 or 304 — which should I order?

316 (CF8M) is the stock material and the one to choose wherever chlorides are present: brine, seawater, coastal air, most chemical service. The molybdenum in 316 is what resists chloride pitting. 304 (CF8) is made to order for general water, air and oil duty.

Kann dieses Ventil zur Reinigung oder Reparatur geöffnet werden?

No. The body is welded, so it cannot be taken apart. That is the trade-off for having no threaded body joint to leak. If you need to service the valve in line, buy the dreiteiliger Kugelhahn instead. If you only need full-port flow and still want no threaded body joint, the seal-welded two-piece ball valve (V-2B / V-2C) is the one to look at.

Ist das ein Volldurchgangsventil?

No. It is a reduced (standard) port valve — the bore is smaller than the pipe. If you need full bore flow, buy the seal-welded two-piece ball valve.

Kann ich daran einen Stellantrieb anbringen?

No. This body has no actuator mounting pad. If you need automation, buy the one-piece pneumatic ball valve, which has the ISO 5211 pad cast into the body.

Können Sie ein Materialzertifikat vorlegen?

Ja. Ein Werkszeugnis ist auf Anfrage erhältlich.

Gibt es bei Ihnen eine Mindestbestellmenge?

Nein. Sagen Sie uns, was Sie benötigen, und wir erstellen Ihnen ein Angebot.