One Piece Stainless Steel Ball Valve – Reduced Port, 316, 1000 WOG, PT/NPT/PF, 1/4″–3″ (R-1B)

Description du produit

A one piece stainless steel ball valve noté 1000 WOG, with the body cast as a single piece and welded closed. 316 (CF8M) is the stock material; 304 (CF8) is made to order. PTFE seats, manual quarter-turn lever, reduced port, −20 °C to +180 °C. Two end builds: femelle × femelle (F×F) de 1/4″ à 3″, et mâle × femelle (M×F) en 1/4″, 3/8″ et 1/2″.

Because the body is one piece instead of two or three bolted or screwed sections, there is no body joint — one fewer place for the valve to leak. The trade-off is honest: it cannot be opened for service, and the bore is one pipe size smaller than the line. We say so plainly further down, and we point you at the valve you should buy instead.

Que signifie réellement « 1 000 WOG » ?

WOG signifie Eau, pétrole, gaz. Une valeur nominale de 1 000 WOG signifie que la vanne est conçue pour Pression de service à froid, sans choc, de 1 000 psi on those media.

Three things buyers get wrong about it:

• Le WOG est un indice de résistance au froid. It is not a steam rating. This valve runs from −20 °C to +180 °C, set by the PTFE seats — tell us your line temperature and we will confirm it suits.
• “La mention ” sans choc » fait partie de la notation. Une conduite soumise à un coup de bélier ou à un démarrage brusque de la pompe présente des pics de pression bien supérieurs à sa pression de service normale. Il faut dimensionner le système en fonction de ces pics, et non de la valeur indiquée par le manomètre.
• On this valve, “gas” means compressed air. Fuel gas lines (natural gas, propane) call for a gas-listed valve, and this is not one.

Si la pression de votre conduite dépasse 1 000 psi à froid, ce n'est pas la vanne qu'il vous faut : indiquez-nous la pression et nous vous proposerons le modèle adapté.

F×F ou M×F — Lequel vous convient le mieux ?

• Femelle × Femelle (F×F) — les deux extrémités sont équipées d’un raccord mâle. Il s’agit du modèle polyvalent, et du seul disponible dans des diamètres supérieurs à 1/2″ (jusqu’à 3″).
• Homme × Femme (H×F) — one male end screws straight into a female port, so you save a fitting and shorten the assembly. Available in 1/4″, 3/8″ and 1/2″ only. If you need M×F above 1/2″, see the two-piece MxF ball valve (1/2″–2″, full port).

Dimensions for both builds are on the PDF dimension sheets at the top of this page.

Caractéristiques techniques

Quand ne pas choisir cette vanne

Applications

A reduced-port, non-serviceable body is a deliberate trade: the smallest envelope and the fewest joints of the three ball valve body types, at the lowest cost of the three. It belongs where those three things matter more than full flow or in-line repair.

• Instrument and gauge line isolation — the shut-off ahead of a pressure gauge or transmitter, so the instrument can be changed without draining the line. Open it slowly; this is an isolation valve, not a throttling one.
• OEM machinery and skid-mounted systems — small-bore utility shut-offs built into a machine frame or a packaged skid, where the valve is replaced as a unit rather than rebuilt in place.
• Installations exiguës — panels, cabinets and pipe runs where a two-piece or three-piece body will not fit. With no mid-body joint there is nothing to add length to the body.
• Compressed air branch isolation — take-offs from a plant air header to a machine, a filter-regulator or a blow-down point.
• Water and oil utility lines — general shut-off on cooling water, wash-down, lubrication and fuel-oil transfer lines up to 1000 psi cold.

Not for pump suction lines (use a full-port valve), fuel gas, steam, potable water or oxygen service — see the table above.

Acheter chez nous

• Manufacturer, not a trading company. Our own factory in Taiwan, stainless valves since 1999.
• Certificat du moulin sur demande.
• One supplier for the whole line — valves, fittings and strainers, one shipment, one set of documents.

Tell us the size, F×F or M×F, 316 or 304, and the line pressure. That is enough for us to quote.

FAQ

What is a one piece stainless steel ball valve?

A ball valve whose body is cast as a single piece and welded closed, instead of being bolted or screwed together from two or three sections. There is no body joint, so there is one fewer place for a line to weep. The trade-off is that the valve cannot be opened for service and the port is reduced — the bore is one pipe size smaller than the line. If you want the same no-body-joint construction with a full-port bore, see the seal-welded two-piece ball valve (V-2B / V-2C).

Que signifie « 1 000 WOG » ?

WOG stands for Water, Oil, Gas. A 1000 WOG rating means the valve is rated for 1000 psi of cold, non-shock working pressure on those media. It is not a steam rating. On this valve “gas” means compressed air — it is not listed for fuel gas.

What is the working temperature range?

−20 °C to +180 °C, set by the PTFE seats. Tell us your line temperature and we will confirm the valve suits it.

Quelles tailles sont disponibles ?

Female × female (F×F) from 1/4″ to 3″ — 1/4″ to 2″ as standard, 2-1/2″ and 3″ on request. Male × female (M×F) in 1/4″, 3/8″ and 1/2″. Dimensions are on the two PDF dimension sheets at the top of this page.

Quelles normes de filetage proposez-vous ?

Le filetage PT (conique) est le filetage standard ; les filetages NPT et PF sont également disponibles en stock.

316 or 304 — which should I order?

316 (CF8M) is the stock material and the one to choose wherever chlorides are present: brine, seawater, coastal air, most chemical service. The molybdenum in 316 is what resists chloride pitting. 304 (CF8) is made to order for general water, air and oil duty.

Cette vanne peut-elle être ouverte pour être nettoyée ou réparée ?

No. The body is welded, so it cannot be taken apart. That is the trade-off for having no threaded body joint to leak. If you need to service the valve in line, buy the robinet à boisseau sphérique en trois parties instead. If you only need full-port flow and still want no threaded body joint, the seal-welded two-piece ball valve (V-2B / V-2C) is the one to look at.

S'agit-il d'une vanne à passage intégral ?

No. It is a reduced (standard) port valve — the bore is smaller than the pipe. If you need full bore flow, buy the seal-welded two-piece ball valve.

Puis-je y monter un actionneur ?

No. This body has no actuator mounting pad. If you need automation, buy the one-piece pneumatic ball valve, which has the ISO 5211 pad cast into the body.

Pouvez-vous fournir un certificat de conformité des matériaux ?

Oui. Un certificat d'usine est disponible sur simple demande.

Avez-vous un volume minimum de commande ?

Non. Dites-nous ce dont vous avez besoin et nous vous ferons un devis.