NAMUR ソレノイドバルブ — 5/2ウェイおよび3/2ウェイ、IP67、24VDC/110VAC/220VAC

製品説明

A NAMURソレノイドバルブ — the pilot that turns an electrical signal into actuator movement. It bolts straight onto the NAMUR interface on top of a pneumatic actuator, with no fittings and no tubing between the two.

Two versions, and which one you need depends on your actuator. Get this wrong and the valve will not work. The table below tells you which one to order.

5/2 or 3/2? Match It to Your Actuator

← テーブルをスワイプしてすべての列を表示 →

This is the single most common ordering mistake in pneumatic valve packages. If you are not sure which actuator you have, tell us the model and we will tell you which solenoid it takes.

仕様

Will It Fit My Actuator?

If your actuator has a NAMURインターフェース on top — the standard bolt pattern and the two air ports machined into the actuator body — this solenoid bolts straight on. No adapter, no piping.

And if you are buying the actuator from us as well: every pneumatic actuator we make has a NAMUR interface. The solenoid, the actuator and the valve all come from us, assembled and tested together, so there is nothing to match up on site.

• Sanitary pneumatic ball valve
• Sanitary pneumatic 3-way ball valve
• Pneumatic butterfly valve

IP67 — What It Actually Buys You

IP67 means the coil housing is dust tight, and that it survives temporary immersion in water. In practice: a washdown bay, an outdoor skid in the rain, a plant room that floods an inch deep. It is the rating you want on any solenoid that lives outside a control cabinet.

あるべき場所

• Automated valve packages — the standard pilot on our pneumatic ball and butterfly valves.
• PLC-controlled plant — turns a controller output into actuator movement.
• Retrofit — adds electrical control to any existing NAMUR-interface actuator, including ones you did not buy from us.
• Washdown and outdoor installations — IP67 coil.

弊社でのご購入について

• 最低注文数量はありません。. Order one to test it.
• 商社ではなく、メーカーです。. Taiwan, valves since 1999.
• Buy the solenoid alone, or the whole package. Valve + actuator + solenoid, assembled and matched before it ships.
• お見積りの回答：24時間以内。.

お見積り依頼 — 24時間以内に返信いたします →

Tell us whether your actuator is double acting or spring return, and what coil voltage you run. That is enough for us to quote.

よくある質問

Do I need a 5/2 or a 3/2 solenoid valve?

5/2 for a double acting actuator, because both air ports have to be fed. 3/2 for a spring return actuator, because only one port takes air and the spring does the return stroke. This is the most common ordering mistake in pneumatic valve packages — if you are not sure which actuator you have, send us the model and we will tell you.

Will this solenoid fit my existing actuator?

If the actuator has a NAMUR interface on top, yes — it bolts straight on, with no adapter and no tubing. That includes actuators you did not buy from us.

Are your pneumatic actuators NAMUR?

Yes. Every pneumatic actuator we make has a NAMUR interface, so any of our solenoids mounts directly onto any of our actuators.

What air pressure does it need?

4 to 8 bar.

What is the air connection size?

G1/4.

What coil voltages do you offer?

24V DC, 110V AC and 220V AC.

What does IP67 mean here?

The coil housing is dust tight and survives temporary immersion in water. It is the rating you want for washdown areas, outdoor skids, and anywhere the solenoid is not inside a control cabinet.

Is there a manual override?

Yes. You can cycle the valve by hand during commissioning, testing, or a power cut.

Can I buy the valve, actuator and solenoid as one package?

Yes, and it is how most customers buy it. We assemble and test the three together before shipping, so there is nothing to match up on site.

最低注文数量はありますか？

いいえ。ご要望をお聞かせいただければ、お見積もりいたします。.