MxF Ball Valve – Male Threaded x Female, 304 Stainless, Full Port, 1000 WOG

PDFV-2D-MF Dimension Sheet
MxF ball valve, male threaded x female · A–G dimensions　PDFをダウンロード ↓

This MxF ball valve has one male threaded end and one female threaded end on a two-piece 304 stainless steel body. The male end screws straight into a tank outlet, pump port or machine connection; the female end takes the next pipe or hose adapter. No extra nipple, and one threaded joint fewer to leak.

Rated 1000 WOG with PTFE seats and a full-port bore, it gives manual quarter-turn shut-off on water, oil and compressed air lines. Sizes 1/2″, 3/4″, 1″, 1-1/4″, 1-1/2″ and 2″. PT threads are in stock; NPT threads and a 316 stainless body are made to order.

主な特徴

• フルポートボア： the bore follows the pipe size to reduce flow restriction and pressure drop.
• MxF ends: one male threaded end and one female threaded end, so the valve mounts directly on equipment without an extra nipple.
• Six available sizes: 1/2″, 3/4″, 1″, 1-1/4″, 1-1/2″ and 2″.
• Material options: 304 stainless steel is in stock; 316 is made to order for chloride service or a higher pitting risk.
• Thread options: PT tapered threads are in stock; NPT threads are made to order.
• Operating range: 1000 WOG pressure rating with a working temperature range of -20 °C to +180 °C.

When to Choose an MxF Ball Valve

An MxF ball valve has an external (male) thread on one end and an internal (female) thread on the other. The male end screws directly into a tank outlet, pump housing or machine connection, while the female end accepts the next pipe or hose adapter.

This arrangement replaces a separate nipple-and-valve combination. It shortens the assembly and removes one threaded joint that could become a leak point. Choose an MxF valve when the valve mounts directly on equipment or at a hose take-off point.

If both ends connect to pipe, a standard female x female two-piece ball valve is usually the better fit. You can also read our guide to ボールバルブの本体タイプ for a comparison of common valve constructions.

主要技術仕様

アプリケーション

An MxF ball valve earns its place wherever the valve has to sit directly on a female port. Typical positions for this 304 stainless valve:

• Tank and vessel outlets: the male end screws into the tank’s female outlet, the female end takes the drain line or hose.
• Pump discharge ports: a direct isolation valve on the pump body, with no nipple between pump and valve.
• Compressor receiver drains: mounted on the receiver’s female drain port for daily condensate blow-down.
• Compressed air drop legs: point-of-use shut-off screwed into the header or manifold outlet.
• Irrigation and dosing manifolds: zone isolation on manifold outlets, with the hose or tubing adapter on the female end.
• Gauge and instrument isolation: the male end goes into the gauge port or process connection so the instrument can be serviced alone.
• Strainer and filter housings: direct connection to female housing ports on line strainers and filters.

Service media are water, oil and compressed air within the 1000 WOG rating. For general plant piping see our 産業用途 ページ。.

よくある質問

What is an MxF ball valve?
MxF stands for male x female. One end has an external (male) thread and the other an internal (female) thread. The male end screws into a female port on a tank, pump or machine, and the female end takes the pipe, so no separate nipple is needed.

Is this a full port ball valve?
Yes. All six sizes have a full-port bore that follows the connected pipe size, which keeps flow restriction and pressure drop low.

どのようなねじ規格がありますか？
PT tapered threads are in stock. NPT threads are made to order. Please state the required thread standard when requesting a quote.

「1000 WOG」とはどういう意味ですか？
1000 WOG means the valve is rated for 1,000 psi service with water, oil or gas at room temperature. Read our WOG 耐圧定格ガイド before selecting a valve for a specific operating condition.

動作温度範囲はどのくらいですか？
The stated working temperature range is -20 °C to +180 °C, limited by the PTFE seats. Actual allowable pressure can change with temperature and service conditions.

316ステンレス鋼はありますか？
304 is the standard stocked material. A 316 body is made to order for applications involving chlorides, seawater, brine or a higher risk of pitting corrosion.